Inconsistent long term RAM data.‏ شرح ‏A portion of the internal RAM is used to store configuration data. At system start, information is read from a non-volatile memory. The information from the non-volatile memory is stored in the portion of RAM used for configuration data. After this initial store, the configuration data should be available fo...

‏Illegal software operation.‏ شرح ‏The DTC is set active if the ECU software executes code that should not be possible to reach, or if the ECU has performed an unexpected reset. The DTC is set inactive after a system reset (provided that the previous fault does not re-occur).‏ علت ‏• Software flaws • Exposure to extensive electro-magnetic radia...

‏Overloaded software resources.‏ شرح ‏The system continuously perform checks of the present CPU load and stack memory utilization. If the load or utilization level exceed limits considered being safe, this DTC is set.‏ علت ‏• Abnormal external conditions such as faulty communication links etc. • Software flaws.‏

‏Consistency check error on node not participating in consistency check function.‏ شرح ‏An unrecognized ECU unit has been detected. It does not match this vehicle. A chassis number has been received from a node not participating in the consistency check function.‏ علت ‏• An ECU unit with a software not compatible with the vehicle, has been conn...

‏Absence of Sensor CAN-bus communication (DAS2 CAN1 buffer overflow)‏ شرح ‏The fault is validated as present if the ECU tries to send CAN-messages on the CAN-bus 1, but no acknowledge is received from other unit(s), and thereby causing the internal buffer in the ECU to overflow. The DTC is set to active if the buffer overflow has lasted for 50 ms...

‏Absence of CAN2 (Front camera bus) communication (CAN2 buffer overflow)‏ شرح ‏The fault is validated as present if the ECU tries to send CAN-messages on CAN-bus 2, but no acknowledge is received from other unit(s), and thereby causing the internal buffer in the DAS to overflow. The DTC is set to active when the buffer overflow has lasted for 50...

‏XBR system state error. BMS configuration fault.‏ شرح ‏The DTC is set active if one of the following conditions is fulfilled for 1 second: • the CAN signal XBR-SystemState, in message ElectronicBrakeController5-A, does not have value "Any external brake demand will be accepted" (0x0) or • the CAN message ElectronicBrakeController5-A has been abs...

‏Loss of function parameters‏ شرح ‏File containing EOL parameters is found to be inconsistent or missing at start of ECU. EOL-parameters could not be read from the persistent memory.‏ علت ‏System supply voltage (U30) was cut off while the ECU was writing to the file containing the EOL-parameters.‏

‏Loss of KWP2000-ECU ID data‏ شرح ‏File containing KWP2000 ECU identification data is found to be inconsistent or missing at start of ECU. The ECU-ID data could not be read from the persistent memory.‏ علت ‏System supply voltage (U30) was cut off while the ECU was writing to the file containing the ECU identification data.‏

‏Loss of persistent IMMO data‏ شرح ‏File containing persistent immobilizer data is found to be inconsistent or missing at start of ECU. Immobilizer codes etc. could not be read from the persistent memory.‏ علت ‏System supply voltage (U30) was cut off while the ECU was writing to the file containing persistent immobilizer data.‏

‏Loss of SOPS data‏ شرح ‏File or files containing the SOPS data, are found to be inconsistent or missing. SOPS data could not be read from the persistent memory.‏ علت ‏System supply voltage (U30) was cut off while the ECU was writing to the file containing the SOPS data.‏

‏Loss of operation data‏ شرح ‏File containing operation data is found to be inconsistent or missing at start of ECU. Stored operation data could not be read from the persistent memory.‏ علت ‏System supply voltage (U30) was cut off while the ECU was writing to the file containing operation data.‏

‏RTC node: timeout in CAN communication.‏ شرح ‏The DTC is set active if the CAN message ADASP1-RTC has been absent for 20 minutes. The DTC is set inactive when the CAN message ADASP1-RTC is received. The DTC is not set in the following cases: • ignition is turned off • first 2 seconds after ignition on • system voltage is below 22 volt • system v...

‏RTC node inconsistent configuration‏ شرح ‏The DTC is set active if one of the following conditions are fulfilled: - The protocol version number in the CAN message ADASP1 (MetaData) does not match the protocol version in the ECU. - The eHorizon sent out by the RTC, at any given time, consists of more than 260 elements. The DTC is set inactive whe...

‏Plausibility test for LDW enable/disable switch has failed.‏ شرح ‏The DTC is set active if the LDW enable/disable toggle switch is active for more than 30 seconds. The DTC is set inactive if the LDW enable/disable toggle switch is inactive for more than 10 seconds.‏ علت ‏• LDW enable/disable toggle switch is stuck. • LDW enable/disable toggle...

‏Plausibility test for AEB enable/disable switch has failed.‏ شرح ‏The DTC is set active if the AEB enable/disable toggle switch is active for more than 30 seconds The DTC is set inactive if the AEB enable/disable toggle switch is inactive for more than 10 seconds‏ علت ‏• AEB enable/disable toggle switch is stuck. • AEB enable/disable toggle sw...

‏DIS2 node inconsistent configuration.‏ شرح ‏The DTC is set active if one of the following conditions is fulfilled: • A faulty chassis number is sent by the DIS2, at least 9 times (msg period time is 5 s --> 9*5 = 45 s). • The CAN message GPM1_DIS has been absent for 135 seconds (9*15 = 135 s time-out) • A chassis number has been sent by DIS2, bu...

‏Electrical error on CAN-bus 4 (CAN4 BusOff)‏ شرح ‏The DTC is set to active if CAN controller of CAN bus 4 is in the state bus-off. The DTC is set to inactive if the CAN-controller is not in state bus-off for 1100 ms. The DTC is not validated (stored) if: • The ignition is turned off • First 2 seconds after ignition on • The supply voltage is bel...

‏DIS2 node: timeout in CAN communication.‏ شرح ‏The DTC is set active if the CAN-message GeneralInfoDISProp has been absent for 300 ms on the CAN bus. The DTC is set to inactive if the CAN-message GeneralInfoDISProp is received. The DTC is not set in the following cases: • Ignition is turned off • First 2 seconds after ignition on • System voltag...

‏Timeout in CAN communication with Forward looking camera (FLC)‏ شرح ‏The DTC is set active if the CAN-message GeneralInfoFLCProp has been absent for 680 ms The DTC is set to inactive if the CAN-message GeneralInfoFLCProp is received. The DTC is not set in the following cases: • ignition is turned off • first 2 seconds after ignition on • system...