‏Forward Looking Camera (FLC) sends invalid values.‏ شرح ‏The DTC is set to active if: CAN message GeneralInfoFLCProp:FLCSensorStatus has values 4-13 (reserved) or 15 (not available) for more than 3 seconds. CAN message GeneralInfoFLCProp:FLCSensorStatus has value 1 (Warming up/Initializing) for more than 7 seconds at startup. The DTC is set to i...

‏Electrical Error on CAN bus 1 (Sensor bus)‏ شرح ‏The DTC is set to active if no messages are received according to the current configuration. Only messages with attached timeout error codes are tested. The DTC is set to inactive if a message is received. The DTC is not validated (stored) if: • the ignition is turned off • first 2 seconds after i...

‏Electrical Error on canbus 2‏ شرح ‏The DTC is set to active if no messages are received according to the current configuration. Only messages with attached timeout error codes are tested. The DTC is set to inactive if a message is received. The DTC is not validated (stored) if: • the ignition is turned off • first 2 seconds after ignition on • t...

‏Electrical Error on canbus 3‏ شرح ‏The DTC is set to active if no messages are received according to the current configuration. Only messages with attached timeout error codes are tested. The DTC is set to inactive if a message is received. The DTC is not validated (stored) if: • the ignition is turned off • first 2 seconds after ignition on • t...

‏Electrical Error on canbus 4‏ شرح ‏The DTC is set to active if no messages are received according to the current configuration. Only messages with attached timeout error codes are tested. The DTC is set to inactive if a message is received. The DTC is not validated (stored) if: • the ignition is turned off • first 2 seconds after ignition on • t...

‏Electrical Error on canbus 5‏ شرح ‏The DTC is set to active if no messages are received according to the current configuration. Only messages with attached timeout error codes are tested. The DTC is set to inactive if a message is received. The DTC is not validated (stored) if: • the ignition is turned off • first 2 seconds after ignition on • t...

‏Electrical Error on canbus 6‏ شرح ‏The DTC is set to active if no messages are received according to the current configuration. Only messages with attached timeout error codes are tested. The DTC is set to inactive if a message is received. The DTC is not validated (stored) if: • the ignition is turned off • first 2 seconds after ignition on • t...

DIS takes too long time to start.‏ شرح ‏The DIS has been stuck for too long in its initialization process (more than approximately 7 seconds).‏ علت ‏The radar might have an internal fault.

‏FLC takes too long time to start.‏ شرح ‏The FLC has been stuck for too long in its initialization process or in its online calibration (more than approximately 15 seconds).‏ علت ‏* The camera might have an internal fault * The FLC could be misaligned, causing the online calibration to fail‏

‏EAS sends essential signals with poor status.‏ شرح ‏Any essential signal sent by the EAS is received with poor status.‏ علت ‏EAS might be degraded and/or has internal faults.‏

‏EAS system state error.‏ شرح ‏The EAS does not accept/support external steering commands.‏ علت ‏* EAS might be degraded and cannot accept steering commands at this time * EAS might have an incorrect configuration * DAS might have an incorrect configuration.‏

‏COO sends essential signals with poor status.‏ شرح ‏Any essential signal sent by the COO is received with poor status.‏ علت ‏* The COO might have an internal fault * The COO might not be configured correctly * Signals sent to the COO from other ECU’s might have poor status‏

‏LKA switch plausibility error.‏ شرح ‏The LKA enable/disable toggle switch is probably stuck.‏ علت ‏* The LKA button has been pressed for too long, so it is probably stuck * The COO has detected a fault in the switch button module which contains the LKA button‏

‏SRR Left Startup Timeout‏ شرح ‏The SRR has been stuck for too long in its initialization process or in its online calibration (more than approximately 15 seconds).‏ علت ‏The SRR might have an internal fault The SRR could be misaligned, causing the online calibration to fail‏

‏SRR Left sends essential signals with poor status.‏ شرح ‏SRR reports limited functionality or any essential signal sent by the SRR is received with poor status. The vehicle is required to be moving for this DTC to be validated and invalidated.‏ علت ‏The SRR or DAS is not configured correctly The SRR unit is not correctly connected to the SRR l...

‏SRR Left internal error‏ شرح ‏The SRR has system status error. The vehicle may be required to be moving for this DTC to be validated and invalidated.‏ علت ‏The SRR has an internal error.‏

‏SRR Left Side: timeout in CAN communication‏ شرح ‏The DTC is set active if the CAN-message ??? has been absent for ??? ms. The DTC is not set in the following cases: * Ignition is turned off * First 2 seconds after ignition on * System voltage is below 22 volt * System voltage is above 30 volt‏ علت ‏Faulty SRR Unit on the Left side. SRR on the...

‏Node inconsistent configuration Side Radar Left side‏ شرح ‏The DTC is set active if one of the following conditions is fulfilled: • a faulty chassis number is sent by the Side Radar on the Left side • the CAN message GPM1 has been absent for 15 seconds (time-out) • a chassis number has been sent by Side Radar, but the DAS vehicle configuration d...

‏SRR Right Startup timeout‏ شرح ‏The SRR has been stuck for too long in its initialization process or in its online calibration (more than approximately 15 seconds).‏ علت ‏The SRR might have an internal fault The SRR could be misaligned, causing the online calibration to fail‏

‏SRR Right sends essential signals with poor status‏ شرح ‏SRR reports limited functionality or any essential signal sent by the SRR is received with poor status. The vehicle is required to be moving for this DTC to be validated and invalidated.‏ علت ‏The SRR or DAS is not configured correctly. The SRR unit is not correctly connected to the SRR...